VTC655065 3.2V 1900mAh LiFePO4 Pouch Battery Pack
| Chemistry / format | LiFePO4 (LFP) pouch cell |
|---|---|
| Model / configuration | VTC655065; one cell with P-1S4604ACE protection circuit |
| Nominal voltage | 3.2V |
| Nominal capacity | 1900mAh at 0.2C discharge |
| Nominal energy | 6.08Wh |
| Pack dimensions | 6.8 × 51.0 × 69.0 mm max. (T × W × L) |
| Charge voltage | 3.65V limit; pack standard charge 3.65 ± 0.03V |
| Charge current | 0.2C standard; 0.5C maximum continuous |
| Discharge current | 1.0C maximum continuous cell rating |
| Operating temperature | Charge 0–45°C; discharge −20–60°C, with current derating by range |
| Cycle criterion | ≥80% initial capacity after 500 cycles at 0.2C, 3.65V charge / 2.5V discharge |
| Cable length | 50 ± 5 mm |
LiFePO4 Pouch Battery Manufacturer in China
VTCBATT supports compact rechargeable designs using LiFePO4 chemistry and pouch construction. This VTC655065 pack pairs one 3.2V, 1900mAh cell with a protection circuit and a 50 ± 5 mm cable. Explore our LiFePO4 pouch batteries and 3.2V LiFePO4 battery range, or send the device load and fit requirements for a configuration review.
For OEM discussions, specify charger voltage, continuous and pulse current, the available enclosure space, operating temperature, cable routing and connector pinout. Available documents and target-market requirements should be confirmed for the final build.
Designed for a compact 3.2V power system
Source-backed electrical and mechanical characteristics for integration review.
3.2V nominal LiFePO4 pouch cell for rechargeable designs.
Assembled pack thickness stays within 6.8 millimeters maximum.
PCM supports overcharge, overdischarge, overcurrent and short-circuit protection.
Three-wire cable measures 50 plus or minus 5 millimeters.
Slim LFP pouch construction
The assembled VTC655065 pack measures no more than 6.8 × 51.0 × 69.0 mm. Its flat pouch construction can be evaluated for compact enclosures where a cylindrical cell does not fit. Allow space for the wire exit and verify compression protection.


Integrated protection board
The P-1S4604ACE PCM provides overcharge, overdischarge, overcurrent and short-circuit functions. The stated 1.0C continuous discharge figure is a cell rating; validate the complete protected assembly against the device load and PCM behavior.
Cable and connector integration
The pack drawing specifies a 50 ± 5 mm three-wire lead and a 3-pin connector, with an NTC lead shown. Confirm the production pinout, mating connector and routing before integrating it into your equipment.

VTC655065 Battery Specification
Electrical ratings, dimensions, test criteria and handling guidance for the 3.2V 1900mAh pack.
Documentation Support & 14-Month Warranty
Review documentation for the target market and ask about the confirmed 14-month warranty for this VTC655065 LFP pouch pack.

Tell us the destination market and required standards so VTCBATT can confirm the certificates, transport records and other documents available for this exact pack. The product specification is available below; no additional approval is claimed here.

This VTC655065 LiFePO4 pouch battery is covered by a 14-month warranty, including two additional months compared with a 12-month period to allow for shipping and customs clearance. Confirm coverage terms with your VTCBATT representative.
Why Choose VTCBATT?
VTCBATT supports custom battery engineering, controlled manufacturing and integration discussions for compact rechargeable designs. Share the target voltage, load profile, enclosure space and connector requirements so our team can review a suitable configuration.
From the raw materials mixing to the cell test, VTCBATT adopts an automatic manufacturing process to maximize production efficiency and enhance the batteries quality, safety, and reliability. The entire manufacturing process is monitored and 100% tested before flowing to the next procedure to ensure zero defects before delivery.
Over the past 20 years, VTCBATT has built strong partnerships with customers in more than 50 countries worldwide. With reliable quality, responsive service, and tailored battery solutions, we have earned the trust of our clients—many of whom have maintained long-term cooperation and lasting friendships with us for over a decade. Together, we continue to grow and move forward toward a brighter future.
Compact Equipment Integration Concepts
Illustrative device layouts; verify each electrical and mechanical requirement before design-in.

Concept for a portable logger; verify enclosure, load profile and operating temperature.

Concept for a compact sensor; check runtime, 3.2V power electronics and charging profile.

Concept for a handheld instrument; confirm pulse current, connector fit and thermal limits.

Concept for a metering backup module; validate standby draw and charge management.

Concept for a compact gateway; verify peak radio load, available volume and recharge conditions.

Concept for a handheld scanner; confirm terminal current, run time and mechanical retention.

Concept for a remote monitoring terminal; check temperature and duty cycle.

Concept for a compact light module; confirm LED load, charging and installation requirements.
Use a charger configured for the specified 3.65V charge limit and confirm the full charge profile during integration. A 4.2V lithium-ion charger is not supported by this specification.
The assembled pack is no more than 6.8 mm thick, 51.0 mm wide and 69.0 mm long. The lead is 50 ± 5 mm; allow extra room for the connector and cable route.
The cell specification permits discharge from −20 to 0°C at up to 0.5C. Charging below 0°C is outside the specified charge range.
The cell specification states 1.0C maximum continuous discharge, equivalent to 1.9A for a 1900mAh cell. Confirm the complete pack, PCM, wire and connector limits for the intended load.
Yes. The documented P-1S4604ACE circuit provides overcharge, overdischarge, overcurrent and short-circuit protection. Confirm the board behavior and pinout in the final assembly.
Related LiFePO4 Batteries
Closest pouch format and voltage, with a lower 1700mAh capacity; compare its dimensions and connector.
Same nominal voltage and pouch family; larger 1S2P construction and different shape.
Same chemistry and voltage with higher capacity and a longer 1S2P pack.
Same chemistry and voltage with a substantially longer 1S2P pack.
Similar nominal voltage and capacity in a cylindrical cell; mechanical format differs.
3.2V LiFePO4 pouch power for compact equipment
The VTC655065 combines a 1900mAh LFP pouch cell with a P-1S4604ACE protection circuit. Its 3.2V nominal voltage and 6.08Wh nominal energy suit product teams designing around a compact rechargeable source. This is a single-cell pack; validate your device electronics against the full voltage range and load profile before integration.
Dimensions, cable and installation
The assembled pack is at most 6.8 mm thick, 51.0 mm wide and 69.0 mm long. The cable length is 50 ± 5 mm. Plan clearance for the wire exit and connector, prevent pouch compression and abrasion, and confirm pinout and NTC interface on the production drawing.

Charging, discharge and protection
Standard charging uses 0.2C constant current to 3.65V, followed by constant voltage. The cell specification lists 0.5C as the maximum continuous charge rate and 1.0C as the maximum continuous discharge rate. The protection circuit provides overcharge, overdischarge, overcurrent and short-circuit functions. Treat the cell, PCM, wire and connector ratings as separate design limits; confirm the complete assembly under your intended load.
Charging is specified from 0 to 45°C, with no more than 0.2C at 0–10°C and no more than 0.5C at 10–45°C. Discharge is specified from −20 to 60°C, with no more than 0.5C below 0°C and no more than 1.0C from 0 to 60°C. The stated cycle criterion is at least 80% of initial capacity after 500 cycles when charged and discharged at 0.2C with 3.65V and 2.5V cutoffs.
Potential application integration
The examples below illustrate possible compact-device layouts, not confirmed deployments. Check voltage, current, runtime, charger, enclosure and temperature requirements for each device.




OEM configuration review
Share your electrical load, operating temperature, mechanical drawing, connector and cable requirements with VTCBATT. The team can review the VTC655065 configuration and available documentation for your target market.










.png)